- #2003 sequoia coolant engine block drain plug install
- #2003 sequoia coolant engine block drain plug manual
- #2003 sequoia coolant engine block drain plug full
- #2003 sequoia coolant engine block drain plug professional
It looks like a 3/8 downward pointing spigot with a 10mm socket-screw sticking out horizontally. Will check freeze protection after a few drive cycles to get it fully circulated, but with a total capacity of 14 quarts, it should be better than 50% concentration. The block drain is located just to the right of the centerline of the vehicle and quite a bit higher than I expected.
#2003 sequoia coolant engine block drain plug full
This is the only full strength extended life coolant made that was available at a reasonable cost. Refilled with 2 full gallons of extended life Peak Asian red/pink concentrate. Did that half a dozen times until finally the water draining out was clean. So I did that and was able to add two gallons of water at a time. So for a few cycles of drain, fill, drive drain, I was only able to add about one gallon of water at time and the stuff draining out was not getting visibly cleaner.Ĭhecked on the Toyota forums and found that you could disconnect the oil cooler water hose at the filter, and that would drain the block better then the drain valve. cummins isc engine coolant sensor location cummins isc engine coolant. Yes it had drain valves on the block, but I wasn't about to risk snapping them off on a 1/2 million mile engine and creating a much worse problem. ( of 4) The 2004 Toyota Sequoia has 7 problems reported for vsc trac light. So my whole cooling system had 1.75 litres coolant and (6.5-1.75) 4.75litres water. Remove the air intake duct from the center. First thing first is you dont need to use ramps for this project as there is already significant clearance under the vehicle. I added 50/50 3.5 litres (ie 1.75 coolant + 1.75 litres water). 6.0L Power Stroke Diesel - Stuck block drain plug - Anyone got a tip or trick to remove the block drain plugs. Rubber mallet Catch pans White lithium grease (optional) Not pictured below is a gallon of distilled water which you will need to mix the coolant with. This means there was 6.5-3.53litres of pure water already in the block etc. Car Detailing and Show & Shine Prep sponsored by Autogeek.Main issue was that both radiator hoses connect to the top of the engine, so draining the radiator will get nearly nothing out of the block not to mention the heater cores. I was only able to get 3.5 litres of the new coolant/water back into the cooling system.Car Audio & Electronics sponsored by Bavsound.Tire & Wheel Forum sponsored by The Tire Rack.Suspension Tech and Handling sponsored by.
#2003 sequoia coolant engine block drain plug professional
Professional Motorsports sponsored by Bimmerworld.Track, Auto-X & Drag Racing sponsored by.General BMW and Automotive Discussion sponsored by Intercity Lines.Quick Navigation 1991 - 1999 (E36) Go Top Use a 3/8 ratchet and a 2.5 in extension to remove the right side plug, and 11.5 on the left side. The right side is easier to get at, and will drain most of the coolant out, so much so that you dont really need to remove the left plug. This will guarantee the uncertainty that if you have tighten the plastic plug enough to avoid leakage. On my car, the plug is tucked up behind the header. The Cooling Fan Assembly is an essential part of a vehicle’s cooling system. I know, why that long?) to purchase a new plastic plug as well. Kia Sorento 2003, Dual Radiator and Condenser Fan Assembly by TYC®. The second thing I noticed was that the plastic plug on the bottom of the radiator was totally rusted (I mean the washer), I would advised anyone who has not done a coolant replacement for 10 years (ye, ye. I was very careful not to apply any force to avoid damage to the O2 sensor. I was able to turn and twist the plug away from the O2 sensor wire. If you know the hole/thread size that would be awesome too.Thank you. /rebates/5738&.com252ffind252f2003-toyota-sequoia-radiator-drain-plug.
#2003 sequoia coolant engine block drain plug install
Im trying to install this adapter so I can run a block heater. Somewhere near the front of the engine hopefully. After loosen the plug, I was able to remove the plug as the plug was shorter than I expected (much shorter than the oil drain plug). Trying to locate a drain plug for the cooling system. The O2 sensor was not really blocking the removal of the engine drain plug totally. Just want to report on my experience regarding the job. Otherwise, I would have surely damaged the O2 sensor and would have cost me a few hundred bucks. It is very helpful in terms of letting me know what I would expect.
#2003 sequoia coolant engine block drain plug manual
Before doing this, I read all the instruction from the manual and the discussion in this forum particular this post. I finally did replacing the coolant on my 1998 328i.
0 kommentar(er)
